wozie12750
Q: What is the diffence between the V1 and the V2. Thanks
Asked by wozie12750 on 2024-01-23 07:10:41Q: Can this be programed for a propeller brake?
Asked by wozie12750 on 2023-12-10 07:54:40
Sushijjgg99 no
2023-12-26 02:23:12 Helpful (0)Q: How many watts does this motor put out on 3S 2200 Li Po?
Asked by wozie12750 on 2021-04-04 06:14:03
Praxig it depends on the propeller you use, 12 inch propeller is 36A, 10 inch folding propeller is 23A.
2021-05-07 05:11:17 Helpful (1)
wozie12750 I have used 11X6 and 12X6 folding props. Get an aluminum hub and spinner don't use the stock plastic one. You should also upgrade the ESC to 40Aor 50A.
2022-08-12 03:24:58 Helpful (0)
wozie12750 Yes.
2022-04-27 06:04:17 Helpful (0)Q: how hard is this to set up for a model and is it possible to use hitec recevers with it ??
Asked by animal1970 on 2022-04-18 06:02:46
wozie12750 The 4 in one module does support some Hitec protocols . There are many videos on you tube that cover model set up and every other option that is in the unit. Not to difficult to set up models with the wizard. I have the mark one unit with open TX , I think many of the units being shipped now are mark two and they have edge TX , I assume the four in one module is still the same only with upgrades and the edge TX firmware.
2022-04-18 08:12:36 Helpful (0)
wozie12750 Choose internal RF, scroll to your RX (2.4gh) model, choose correct protocall. Assign a number to the RX . If necessary install bind plug, energize RX then click on bind.
2022-03-09 10:10:38 Helpful (0)Q: Will this work with a Spectrum DX6e?
Asked by wozie12750 on 2019-09-30 06:38:20
Artur yes
2019-10-19 03:24:57 Helpful (1)Q: Is a carrying case included?
Asked by BG126171794 on 2022-01-22 07:55:19
wozie12750 No but it comes in a very robust foam case in a cardboard box. I have been using the hard foam case and putting it back in the box to transport. No problem, works great and looks like it will last years.
2022-01-22 06:17:27 Helpful (0)
wozie12750 Works excellent in English.
2021-12-07 05:59:12 Helpful (0)
Q: What improvements does the V2 have over the original version ?
Asked by wozie12750 on 2021-05-26 07:53:31
GroundControlRC Fromwhat I can glean the V1 was optimized for 4S. The V2 is optimized for 3S. The V2 is supposed to have denser foam than the V1 and all servos on the V2 are listed as 9g Digital Metal Gear while one of the Servos on the V1 was Nylon Gears. The V2 is listed as having a smaller Motor than the V1 probably because it's optimized for 3S not 4S. I hope that helps. See you in the Air! Ground Control RC
2021-06-03 01:30:05 Helpful (1)
We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
