anglovirtual
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

anglovirtual 17/08/2019
Great props in a fun choice of colours. Its worth noting that even though these are called ‘Pro’ props they are just the same as the regular Cyclone 5047c props, except these can also be used with the ‘pop-on/off’ motor threads. But they work just fine on normal motors without this feature too.
6 Pairs DALPROP Cyclone 5 Inch T5047C Pro 3-blade POPO Propeller Racing Drone
US$8.02 US$8.23
0
Recommendations
Comments (0)
anglovirtual 13/04/2018
As others have said the port labelled rx6(S) is S-Bus If you’re running an FrSky receiver and you want telemetry you need to enable Softserial in Betaflight/Butterflight as this FC doesn’t appear to have a built-in inverter. You can then map Softserial to a free port on a UART via the Betaflight CLI and run Smart Port telemetry through that port. I enabled Softserial on the LED_STRIP port on mine as it was free and it meant I could solder all my RX wires next to each other on this board. Google ‘How to use Betaflight Softserial’ for a tutorial if you don’t know how to do this.
9g 30.5x30.5mm Omnibus F4 Flight Controller AIO OSD 5V BEC Current Sensor for RC FPV Racing Drone
US$22.79 US$38.99
4
Recommendations
Comments (2)
anglovirtual 18/09/2018
This is a fantastic frame for the money. Carbon is pretty good quality and frame feels stiff and strong. Easy to work on and remove arms etc. The lower top deck design compared to the Martian means a lower center of mass and gives more locked-in stable flight performance. Plenty of space inside to mount a stack and your VTX RX etc. compared with tighter frame designs like the Chameleon. Flight performance of this compared to a Reverb is petty much identical. Only thing wrong with it is the screws are pretty poor quality and strip easily so it’s definitely worth replacing these at the start.
Realacc Real4 220mm Wheelbase 4mm Arm X Structure Frame Kit with PDB Board for RC Drone FPV Racing
US$26.77 US$49.99
2
Recommendations
Comments (0)
anglovirtual 08/07/2018
I've had BIG issues with mid throttle oscillations using this flight controller on my Chameleon frame. I soft mounted the motors and f.c and no matter what I did with the PIDS the quad would bounce and vibrate in forward flight in anything over a slight breeze. Changing prop types made no difference either, nor did switching from 16k/16k to 8k/8k or 4k/4k on the PID loop and the motor vibrations were low to the gyro. So I think the gyro chip on my board must be faulty or slighlty loose as it seems WAY too sensitive and the flight performace is poor. Either that or this F.C does not like frames with one-piece carbon base plates.A So be warned if you have a Chameleon-style frame! Overall very disappointed with this flight controllers performance, especially considering the cost.
Holybro Kakute F4 AIO All in One V2 Flight Controller STM32 F405 MCU Integrated PDB OSD for RC Drone
US$47.82 US$63.99
0
Recommendations
Comments (0)
PUDA X220 5 Inch 220mm Wheelbase 4mm Arm Carbon Fiber Racing Frame Kit for RC Drone
US$34.50 US$50.00

Q: Are spare screws available for this frame?

Asked by anglovirtual on 2018-07-06 01:24:10

SLICK6 Yes there is varied screw sizes available, Try the box sets of 3m screws with different sizes inside.

2018-11-04 04:47:51 Helpful (0)
Submit
Answers (2)
anglovirtual 30/06/2018
These are decent VTXs when they work. I’ve had a few of these now and one broke in a crash (my fault) and another was left powered-on for an hour when my quad got stuck up a tree. After that it still worked but had really bad black lines in the video feed in flight so I guess it overheated. Currently on my 3rd and no issues - so if you don’t abuse them they seem to be fine! And at this price you can’t really complain...
Eachine TX801 5.8G 72CH 0.01mW 5mW 25mW 50mW 100mW 200mW 400mW 600mW Switched AV VTX FPV Transmitter For RC Drone
US$29.99 US$55.99
0
Recommendations
Comments (0)
9g 30.5x30.5mm Omnibus F4 Flight Controller AIO OSD 5V BEC Current Sensor for RC FPV Racing Drone
US$22.79 US$38.99

Q: Does this board have a built-in inverter for telemetry with Frsky?

Asked by anglovirtual on 2018-04-12 11:22:23

Ebul lience NO

2018-05-04 02:10:11 Helpful (0)
Submit
Answers (1)
anglovirtual 27/03/2018
Made of tactile stretchy plastic that easily fits over the switches on my Taranis radio even stretches over the wider ones! The sticky plastic gives a more positive grippy feel to the switches against my fingers which is nice. You get a decent amount in one bag more than enough for one radio- but 2 packs might be necessary if you want them for 2 radios. Good product!
10Pcs Rubber Transmitter Anti-slipping Stick Switch Cap Sheath for Flysky Futaba JR Frsky Radiolink
US$3.23 US$8.99
0
Recommendations
Comments (0)
anglovirtual 28/01/2018
I've had four of these on my quad for over a year now and they are still working well. Only had one LED bulb fail in that time, but as there are two LEDs on each unit I've still got light! :) I've not noticed any difference in flight times on my quad with these fitted vs my identical second quad with no LEDs - so they don't seem to drain your battery on 4S. They seem pretty robust and can take plenty of crashes without issue. Just make sure you put some liquid electrical tape over the solder pads before you fly, as if you leave them unprotected it will cause a short circuit in damp or wet grass!
Eachine Wizard X220 X220S RC Drone FPV Racing Spare Part LED 12V Motor Mount for 1806 2206 Motor
US$4.37 US$8.99
0
Recommendations
Comments (1)
anglovirtual 07/01/2018
Looks and performance-wise these motors are pretty good. They have quite a lot of low-rpm torque but seem to lack outright punch at high rpms that my Emax rs2205s motors have. They seem happiest at low to mid throttle. However they are quite expensive for what they are and the metal they are made from is quite soft which means they are not very strong and are pretty vulnerable to significant damage in harder crashes. The motor bell can be easily bent out of shape if it takes a direct impact which then jams on the base and stops the motor spinning. All of this wouldn't be such an issue if they were built stronger and didn't cost so much to replace! So value for money is an issue with these...
DYS Fire 2206 2100KV 2300KV 2600KV 3-6S Brushless Motor For 200 210 220 280 for RC Drone FPV Racing
US$21.00 US$26.77
2
Recommendations
Comments (0)
anglovirtual 06/01/2018
For the price these are a worthwhile purchase for that little bit of extra protection for your motors. However they dont make you invincible! Crashed my quad from 15ft up onto slightly hard ground the other week and the rear left arm took the brunt of the impact. It snapped my motor protector clean in half and bent the motor bell meaning the motor wouldnt spin - so theyre not fool proof but better than nothing!
LDARC Universal Motor Cover Protection for 22 Series Motors M3*8 for RC Drone FPV Racing
US$4.88 US$9.99
1
Recommendations
Comments (0)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe