gugi9000
Q: Can i use this to get video from any analog quad camera? Just connect to dji goggles and thats it?
Asked by BG163812451 on 2021-10-31 04:03:39
gugi9000 You need to get an analog receiver as well. This is just the adapter part.
2021-10-31 05:58:48 Helpful (0)Q: what is the maximum power output?
Asked by cwchapma on 2021-09-04 07:29:34
gugi9000 250mW
2021-09-26 03:38:08 Helpful (0)
gugi9000 The XT30 is to ease the load on the internet batteries of your transmitter.
2021-09-26 03:35:29 Helpful (0)Q: Does this work with radiomaster tx12?
Asked by BG163812451 on 2021-09-23 07:26:56
gugi9000 Yes. This is unrelated the the transmitter to receiver. This is analog video only.
2021-09-26 03:34:51 Helpful (0)
gugi9000 Yes and no. The VTX transmits analog signal on 5.8 Ghz, but the camera also records 1080p to an SD-card plugged into the quad.
2021-08-09 04:37:30 Helpful (2)Q: autonomie???
Asked by alpatch2 on 2021-01-09 03:33:26
gugi9000 No
2021-08-03 01:51:04 Helpful (0)Q: Hi guys, will it connect with TBS UNIFY PRO 5G8 HV RACE?
Asked by Paskraidysim on 2021-06-02 07:45:44
gugi9000 Yes.
2021-08-03 01:42:07 Helpful (0)
gugi9000 No. It’s has a 5.8 GHz receiver for analog FPV drones.
2021-07-31 09:56:59 Helpful (0)
gugi9000 No OSD or anything? Sounds like your device is broken. Contact support.
2021-07-17 02:15:58 Helpful (0)Q: the stack specification says input: 4s and the ESC says input: 2-5s. so can I run 5s on this or no?
Asked by yamesve on 2021-07-16 09:56:06
gugi9000 No. That is burst current. You might fry the FC (or the ESC) if you do so.
2021-07-17 02:14:15 Helpful (1)Q: can these take normal props? like gemfan for example?
Asked by BG561054346 on 2021-06-20 11:32:56
gugi9000 This is for like 3 or 4 inch props with a 1.5 mm center hole and two screws (so, I guess: no)
2021-06-20 01:14:29 Helpful (0)Q: What are the motor and shaft dimensions?
Asked by JayGeeBSE on 2021-05-22 09:13:28
gugi9000 1.5 mm
2021-05-23 06:13:34 Helpful (1)Q: Is it High Voltage (4,35V) batteries? Or max voltage is 4,2V?
Asked by BG403217573 on 2021-05-23 04:59:31
gugi9000 It’s HV 4.35V. Says right there in the description ;-)
2021-05-23 06:12:56 Helpful (2)
gugi9000 Does your printer otherwise match the picture of the Ender 3Xs Pro on this page?
2021-04-17 11:41:45 Helpful (0)
gugi9000 It does.
2021-04-15 12:20:33 Helpful (0)
gugi9000 No.
2021-04-13 10:20:04 Helpful (0)
We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
gugi9000 18 watts. See the description 😉
2021-11-13 12:21:03 Helpful (0)