Kris
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

Kris 27/10/2023
Overall a decent fence, however, there are a couple of material issues as well as design issues. 1. Fence stops pieces are made of aluminium base and plastic composite stop piece. The bolt-washer combo which holds the stop piece is undersized for this stop. As a result, it bends easily even with not much force. This is a bad design in combination of a poor choice of materials. 2. The fence micro adjusters are badly designed (too small) and also they cheaped out on the connection design which is done by a bolt-plastic slot combination. It works, but it is not convienient to use and the slack in the connection is huge. I chose not to use it at all. 3. The big stop bolt system has an aluminium turn head but base is plastic. Works, but have to be careful not to break it by tightening the bolt with too much force. Aluminium base part should have been used instead.
ENJOYWOOD Wnew Woodworking Router Table Fence Aluminium Profile Fence System 700mm with Sliding Brackets Bit Guard
US$175.99 US$399.99
1
Recommendations
Comments (1)
Kris 09/11/2023
Quality control of packaging is bad. I ordered 12 tracks. 1 out of 12 came in without being properly packed with missing screws and end damaged because of missing the wrap package. I would give this a 3-star rating, but they would filter it out.
1Pc 800mm T-slot T-tracks Miter Track Jig Fixture Slot Tool for Router Table
US$15.42 US$18.99
0
Recommendations
Comments (1)
Kris 07/11/2023
The quality is acceptable. The packaging was a bit sloppy. Whoever packed this thing did put the loose steel bolts with a same slot with the miter gauge and it got some cosmetic damage. Otherwise its OK. The only problem I have with its functionality is that the right side is 90 degrees. That means it cant do 45 deg cuts without offseting. This can be annoying for many. I would have preffered it to be 45 deg.
HONGDUI HD-MG21 Miter Gauge with Extended Fence for Woodworking Table Saw Router Table Precision Angle Setting
US$255.99 US$399.99
0
Recommendations
Comments (1)
Kris 27/10/2023
Good tool. Quality as expected. Keeps its 90degree angle when tightened.
ENJOYWOOD Adjustable 300mm Aluminum Alloy Combination Square 45 90 Degree Angle Scriber Steel Ruler Woodworking Line Locator Ruler DIY Carpenter Measuring Tool
US$10.99 US$25.99
0
Recommendations
Comments (0)
Kris 27/10/2023
Good tool. Quality as expected. I little pricy, but well worth it.
HONGDUI Woodworking Chamfer Plane with 3 Replacement Carbide Insert Double Cutter Edge Corner Plane Chamfering Planer for Quick Edge Trimming of Wood
US$65.99 US$99.99
0
Recommendations
Comments (0)
Kris 27/10/2023
Good tool. Quality as expected for the price.
Wnew 3D Table Saw Pushblock Woodworking Table Saw Safety Pushblock
US$69.99 US$79.99
0
Recommendations
Comments (0)
Kris 26/10/2023
The price is a bit much, but the product is well made. A couple of issues when assembling. a. for some wierd reason a 10mm wrench was included. That was useless, since there is no 10mm bolts or nuts on this thing. Intead there should have been a PH3 screwdriver. b. One steel slider insert had a very bad thread and I was forced to make a new one for it. Luckily I had a right tools for it. I calibrated by making an actual cut and adjusted brackets according to the real outcome. This is a better way to get accurate calibration. When in full lenght the tool was off by 1mm at 1200mm mark. So I had to sand two outer pieces a little shorter to make it fully accurate. When all that was done, everything worked fine and the cuts were up to 0.3mm accurate for all lengths. Overall I am happy with it.
ENJOYWOOD Upgraded Aluminum Alloy Parallel Guide System for Repeatable Cuts for Track Saw Rail Fit for Makita and Festool Woodworking Tools Hook Upgrade
US$129.99 US$199.99
0
Recommendations
Comments (1)
20x20mm Geprc Stable Pro F7 Stack Dual Gyro F7 Flight Controller & 35A BLheli_32 4in1 ESC & 5.8G 500mW VTX for RC Drone FPV Racing
US$147.99 US$150.00

Q: The length of the m2 bolts?

Asked by Kris on 2019-08-05 02:07:04

Alvaro Navarro puedes hablar en espanyol?

2020-02-19 12:19:56 Helpful (0)
Submit
Answers (1)
Kris 25/07/2019
Fine props. 0.4g and work well
Happymodel Sailfly-X Spare Part 6 Pairs 65mm 2-Blade Propeller w/ 1.5mm Mounting Hole for RC Drone FPV Racing
US$5.99 US$9.99
0
Recommendations
Comments (0)
iFlight SucceX mini F7 TwinG V3 F722 Flight Controller & 35A 2-6S DSHOT1200 ESC & pit/25/100/200/500 VTX
US$92.69 US$101.97

Q: The length of the m2 bolts?

Asked by Kris on 2019-08-05 02:07:15

tiemfpv about 20mm

2019-08-14 10:21:35 Helpful (0)
Submit
Answers (1)
Kris 25/07/2019
Works as advertised.
Runcam Racer Nano CMOS 700TVL 1.8mm/2.1mm Super WDR Smallest FPV Camera 6ms Low Latency Gesture Control Integrated OSD for FPV Racer Drone
US$35.86 US$38.39
0
Recommendations
Comments (0)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe