BG184854824
Q: Is ZT-X Digital Multimeter button 9999 is the replica of ANENG Q1 Digital Multimeter 9999 ?
Asked by gofordina_59 on 2020-01-07 12:02:28
DolphinSauce The firmware is flashed onto the board, there is no technical software
2022-03-25 01:24:49 Helpful (0)
marianbinu Both of them.
2022-03-18 06:18:48 Helpful (0)Q: Instructions manual paper and pdf and software?
Asked by gofordina_59 on 2019-01-02 10:36:00
sri_raoul @Pinfar: your answer... is it a joke??? How can we do to assembly the leds?
2019-03-28 03:59:39 Helpful (11)Q: What is the lens magnification ?
Asked by BG184854824 on 2020-01-26 09:45:28
en_srl hard to tell, but not too much.
2021-10-06 01:43:08 Helpful (0)Q: What are the minimum & maximum voltage & current?
Asked by gofordina_59 on 2019-07-21 01:29:40
BG179115112 12vminim . maxim 24v. curentul maxim 2500ma
2020-08-19 12:53:40 Helpful (1)Q: What are the minimum and maximum voltage & current?
Asked by gofordina_59 on 2019-07-21 01:28:14
KthulhuFhtagn i think its 5-19v but be careful of amperage and polarity
2021-09-27 01:56:19 Helpful (0)Q: How to delete a question the one who have questioned ?
Asked by gofordina_59 on 2019-01-01 10:25:01
shlongeee idk
2021-07-20 06:57:21 Helpful (0)Q: Can this soldering station will work from 12 Volt DC ?
Asked by BG184854824 on 2020-01-22 07:55:39
luciankerestes da12vdc cu 3amp
2021-01-12 09:56:55 Helpful (0)Q: What are the minimum and maximum voltage & current?
Asked by gofordina_59 on 2019-07-21 01:28:16
BG393815561 12 volts min and 24 volt max, 2500ma
2020-10-07 08:15:14 Helpful (0)
DrLuvGluvDDS 10
2020-03-31 04:32:21 Helpful (1)
spletko Use link above to get assembly instruction, which you can magnify (zoom) and print in details.
2020-08-28 05:21:09 Helpful (0)
Marc with me everything was just there
2020-08-19 05:07:57 Helpful (0)
kharar Probably because cell 2 and 4 are only 4.1V, the rest are 4.2V
2020-06-11 06:06:41 Helpful (0)Q: What is the minimum and maximum resistance that Aneng V8 can measure?
Asked by gofordina_59 on 2019-07-30 09:43:25
Michel Walsh It is difficult to measure resistance of about 1 Ohm with precision using only two wires as probe (better using 4 wires with a so called Kelvin setting). The specs mention a precision of 1.5% precision for around 80 Ohm. So, in the end, it strongly depends on the precision that you seek..
2020-06-10 08:26:19 Helpful (1)Q: Any demo video on 10g Weak Acid Soldering Solder Paste Solder Flux Grease Paste ? How to use it ?
Asked by gofordina_59 on 2019-12-23 12:25:49
Spidery Method of use : 1. Using the end of a match or toothpick, apply a little soldering paste to the leads that will be soldered. 2. Place the soldering iron tip over the leads. Contact the solder against these leads. Heat the solder till it flows freely, then quickly move the soldering iron and solder away.
2019-12-29 11:56:53 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
farkasditke73 It's a rebranded XT-X.
2023-11-19 12:16:21 Helpful (0)