NightOne
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

NightOne 03/09/2021
Very fast delivery, very happy with device, waterproof and well made, took me about 10 min to replace old keypad with new. The only negitive that I have found is that you can only have a 4 digit public code. Not a big issue for me because I use card and pin code. Also pairing with Tuya app is very easy to set up. Would definelty recommend.
WIFI Tuya Smart Door Lock Door Access Control System Standalone Keypad 125KHZ Card Door Entry Access Controller
US$23.77 US$39.87
0
Recommendations
Comments (0)
NightOne 03/09/2021
Very well made and great fun to put together, I would recommend watching youtube videos on the set by set build process as it helps a lot. One very important issue when building is to make sure you push the PTFE tube all the way into the hot end...it has to go in about 5 cm...I made the mistake of not pushing it in far enough as I felt resistance and didnt want to force it....this caused the hot end to jam and I had to take hot end part to clean the jam (youtube "how to" again). I have on negitive about the quality of the filament extruder, it only has a single drive and it skips like crazy right from the start... its also made out of plastic and you need to be really carefull screwing it down otherwise you will crack the plastic. I tried for 3 days to get it to work properly and eventually gave up and replaced it with dual drive extruder from old printer. One huge plus is the hot end and the cooling...the dual fan cooling is fantastic, but does cause one issue....when you upgrade the firmware yourself to the latest Marlin you need to tweak the thermal runaway settings....the fan is so effective that when it turns on after the first layer it triggers a thermal runaway error (hot end temp drops 11 degrees in two seconds) and the print stops..... I would also recommend upgrading the stepper drivers to TMC 2208s as they are much quieter and improve the print quality greatly.. I am extremely happy with this printer.
HOMERS/TEVO® Tarantula Pro 3D Printer Kit with 235x235x250mm Printing Size MKS GenL Mainboard 0.4mm Volcano Nozzle Support 1.75mm Filament
US$229.99 US$434.76
0
Recommendations
Comments (0)
TPA3116 2.1 DC 12V-24V 50W+50W+100W HIFI Digital Audio Amplifier Board
US$22.90 US$34.99

Q: in this board from where can i extract 5 volts ?

Asked by Nehal Rai on 2019-01-16 01:58:13

NightOne Turn the board over....under the board you will see Vout 5v output...120mA

2019-02-06 01:06:27 Helpful (1)
Submit
Answers (3)
SL-LC 01 Super Mini LED WIFI Smart RGB Controller For RGB LED Strip Light DC 5-28V
US$9.47 US$19.99

Q: can i connect this to a pc?

Asked by IMohd on 2019-01-01 09:13:54

NightOne You can use node-red to control this from a PC.....Just search for node-red-contrib-magichome-controller on flows.nodered.org

2019-01-08 02:06:53 Helpful (0)
Submit
Answers (1)
NightOne 19/06/2018
Installed in less then 5 min on garage door.... very easy to install...both remotes where programed so I didnt have to "teach" the controller.... there was no jumper included on the pins...so had to use a old jumper bridge from computer... Instructions on banggood say that momentary is idle (jumper)....which I assume means no jumper but thats was not true of mine...I had to bridge jumpers 1-2 to set it to momentary...meaning hold button A to switch relay on....let go button A to switch relay off. Works great.
DC12V 433MHz Relay 1CH Wireless RF Remote Control Switch Transmitter for Light
US$16.99 US$20.99
1
Recommendations
Comments (0)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe